- X10 activehome pro cm15a usb transceiver install#
- X10 activehome pro cm15a usb transceiver drivers#
- X10 activehome pro cm15a usb transceiver skin#
- X10 activehome pro cm15a usb transceiver software#
If you have complicated electrical wiring in your house the power line signaling may not work right. Also, it’s the kind of gear that for some percentage of people will be problematic. However, it should not be used for mission critical purposes.
X10 gear is a lot of fun and is used reliably by millions of people worldwide. Be aware, if your home has a lot of RF interference from other devices you may not receive a clean video feed. This allows you to have the camera anywhere in your home as long as it is within range of the receiver so you are not limited by the length of a USB cable as you would be with a direct connect camera. The camera in that package has transmits via radio frequency ( RF) to a receiver. If you want to have the camera far away from your PC, you might consider the Ninja/Camera combination. If you have trouble, try the X10 technical support forum for help.įor my setup I just have the CM15A transceiver and a standard USB web camera that I clipped on to the Ninja Pan N Tilt camera turret. However, check to see if there are newer ones just in case:
X10 activehome pro cm15a usb transceiver drivers#
At the time this was written, the latest drivers could be found using the link below and the file name to download was x10drivers_6432_239.exe. Make sure you have the latest drivers installed for the CM15A transceiver or your gear will not work right. I have not used it but if you’re looking for that kind of capability, that may be an additional item to get.
X10 activehome pro cm15a usb transceiver software#
X10 also has a software package that allows you to control your camera turret over the Web and stream video to you remotely. This package includes the CM15A transceiver and software. The best way to get started, if you don’t have it already, is to get the X10 ActiveHome Professional package. This allows it turn X10 modules on and off and to pan, tilt, and center the Ninja turret amongst other operations. It transmits signals both along the power lines running through your home and via radio frequency ( RF) using its antenna. The CM15A is the bridge between your Windows PC and the X10 gear you have in your home. If you want your camera to track your face with this utility you will need at the very least the X10 CM15A transceiver and the Ninja Pan ‘n’ Tilt camera turret. Naturally, the camera won’t pan and tilt to follow your face without a turret, but you can watch the system detect your face and then track it via the colored boxes it draws around your face to show you where it thinks your face is currently. You can run the FaceTrack utility without a camera turret as long as you have a standard Windows web camera. The Client tab is for actions.If you like robots and high tech gadgets, or want to be notified when new versions of the FaceTrack utility are available, subscribe to the mailing list using the form below. Configure the plugin (Only the Server Tab is required.
X10 activehome pro cm15a usb transceiver skin#
Copy the contents of the Skin\Blue3Wide folder to your skin folder.Ĥ. Unzip and copy the contents of the Plugins folder to your MediaPortal\Plugins\Windows folder.ģ. Note: To test a device, hightlight the row and click the Test On or Test Off buttons.Ģ. Enter a port number (if you desire a different port number)
X10 activehome pro cm15a usb transceiver install#
Click on the Install Service Button (this will install the service)ĥ. Go into MP Configuration and configure the X10 Process (See Image 1 below)Ĥ.
Install the setup file (Be sure to remove everything to do with prior X10 tests we have done.)ģ. Download the X10ServerSetup 0.2.zip file.Ģ. Configure your devices in ActiveHome Pro (if not already done.) NOTE: Be sure the X10 Device Network Service service is installed and running.ġ. Install ActiveHome Pro software (if not already done.)Ģ. NOTE: If you installed the previus version, PLEASE go into MP Config and Stop & Uninstall service before installing this 0.2 version.ġ. Everything can be configured through the Process Plugin now. This package contains two parts, the first being the windows service and the second being the MP Process Plugin. This is the second build of the Server Configuration tool for the X10 Home Automation service.
0 kommentar(er)
